JoaquinBordado21
Leecher
- Joined
- Jan 27, 2023
- Posts
- 5
- Reaction
- 4
- Points
- 3
*Connect the LAN1 port of Converge to the WAN port of your secondary router.
*On Huawei Converge router
1. First step, access mo muna yung web browser page or web portal ni Converge 192.168.100.1 using superadmin (research nyo na lang, baka ma-ban kapag pinost ko eh)
2. Look for FIREWALL setting
- Disable and apply
3. Look for DHCP setting
- Disable and apply
4. Look for the WAN setting
*On your Secondary Router
1. First, access mo muna yung web portal ng router mo 192.168.0.1 (depende sa brand check mo na lang).
2. Go to WAN section or dun sa may MTU baka nandun.
3. Then, look for the option na may Clone MAC Address or Use MAC Address
5. Go to your secondary router LAN settings. You can set your new LAN pool or leave it as is.
*Reboot both the Converge router and your Secondary router
*To determine if true bridge ang nagawa mo, connect to your secondary router.
- dapat LAN IP address mo yung makikita sa "connected router" mo (192.168.0.1 or depende sa setup mo) pero yung WAN IP mo is something like 10.188.x.x or 10.187.x.x
*Take note, kapag naka-bridge ka, di mo na ma-access yung web portal ni Converge, pero lahat ng settings ay control na ng Secondary router mo.
*Kahit ilang beses mo irestart yung modems mo, di na ma-break yang bridge na yan, unless mag-hard reboot ka ng Converge router.
*On Huawei Converge router
1. First step, access mo muna yung web browser page or web portal ni Converge 192.168.100.1 using superadmin (research nyo na lang, baka ma-ban kapag pinost ko eh)
2. Look for FIREWALL setting
- Disable and apply
3. Look for DHCP setting
- Disable and apply
4. Look for the WAN setting
- Click 2_INTERNET_R_VID_10
- Take note of the MAC Address (kelangan makuha mo muna ito. Napakaimportante nito para makapag-create ka ng true bridge)
- Kapag nakuha mo na ang MAC, change mo na yung setting from "Route WAN to Bridge WAN" ng 2_INTERNET_R_VID_10 then click apply.
*On your Secondary Router
1. First, access mo muna yung web portal ng router mo 192.168.0.1 (depende sa brand check mo na lang).
2. Go to WAN section or dun sa may MTU baka nandun.
3. Then, look for the option na may Clone MAC Address or Use MAC Address
- Dito mo ilalagay yung MAC Address na pina-take note ko sa'yo kanina galing dun kay Converge 2_INTERNET_R_VID_10
- Once mailagay mo na, click apply
5. Go to your secondary router LAN settings. You can set your new LAN pool or leave it as is.
*Reboot both the Converge router and your Secondary router
*To determine if true bridge ang nagawa mo, connect to your secondary router.
- dapat LAN IP address mo yung makikita sa "connected router" mo (192.168.0.1 or depende sa setup mo) pero yung WAN IP mo is something like 10.188.x.x or 10.187.x.x
*Take note, kapag naka-bridge ka, di mo na ma-access yung web portal ni Converge, pero lahat ng settings ay control na ng Secondary router mo.
*Kahit ilang beses mo irestart yung modems mo, di na ma-break yang bridge na yan, unless mag-hard reboot ka ng Converge router.