Troubleshooting is the presence of abnormalities on our computer. Computer problems or troubleshooting is divided into 2 hardware troubleshooting and software troubleshooting.
Troubleshooting hardware are usually marked with the computer can not be turned on, the monitor is dead and so on. While troubleshooting software is characterized by slow computer performance and others. Though not close the possibility also the symptoms of slow computer happens not only in software but also hardware troubleshooting.
How to resolve troubleshooting standard on a computer can be said first aid on computer problems occur the troubleshooting analysis and how to resolve it can refer to hardware troubleshooting solutions on a pc computer.
In the discussion this time tricks-collections.com will be discussed with more of a focus how to cope hadrware troubleshoting on pc of your computer, as follows:
The sound of ‘beep’ short 1 time, it means the system has done a Boot process properly.
The sound of ‘beep’ short 2 time, it means there is a problem on the configuration or settings in the CMOS.
The sound of ‘beep’ long 1 time and short 1 time, it means there is a problem on the Motherboard or DRAM.
The sound of ‘beep’ long 1 time and short 2 time, it means there is a problem on the monitor or VGA Card.
The sound of ‘beep’ long 1 time and short 3 time, it means there is a problem on the Keyboard.
The sound of ‘beep’ long 1 time and short 9 time, it means there is a problem on the ROM BIOS.
The sound of ‘beeps’ long continuous, it means there is a problem in DRAM.
The sound of ‘beeps’ short continuous, It means there is a problem receiving the voltage (power).
On some brands of Motherboards will emit beeps a few times when the temperature of the processors are too high (hot). Although there is a possibility there is also a difference in the sound of “beep” on any brand of motherboard doesn’t hurt you more able to observe and monitor troubleshooting that occurred on your computer. Because basically sound analysis it is not certainly in detecting and troubleshooting but could become the discourse for us when there a troubleshooting on our computer.
Hardware Detection Problems:
If there is a problem with computer system still gives the appearance of a message on the monitor or accompanied by the sound of “beep” is 1 or 2 times, then chances are there are problems in the layout of the component numbers 6, 7, and 8 are on the Keyboard, Card i/o, and Disk drives.
If there is a problem with the system provides the code “beep” is more than 2 times, then chances are there are problems in the layout of the component numbers 4 and 5, i.e., RAM, VGA Card and Monitor.
As for the problem that is not accompanied by a message on the monitor or sound “beep” code, chances are there are problems on the component numbers 1 and 2, i.e. the Power Suplly and Motherboard.
For the initial stage, there is the first analysis where the computer hardware troubleshooting. Then you can revoke or relinquish the hardware approximately occurs troubleshooting then attach it back with for sure and check out exactly no leniency in return the hardware installation.
If there is still some undiscovered troubleshooting please check to the nearest computer service or authorized service center for your computer.
Troubleshooting hardware are usually marked with the computer can not be turned on, the monitor is dead and so on. While troubleshooting software is characterized by slow computer performance and others. Though not close the possibility also the symptoms of slow computer happens not only in software but also hardware troubleshooting.
How to resolve troubleshooting standard on a computer can be said first aid on computer problems occur the troubleshooting analysis and how to resolve it can refer to hardware troubleshooting solutions on a pc computer.
In the discussion this time tricks-collections.com will be discussed with more of a focus how to cope hadrware troubleshoting on pc of your computer, as follows:
- Check the power to the computer: Power cable, Power suply check back it is installed properly and correctly and no problems.
- Make sure that the installation of computer components right: make sure there is no slack in the component installation.
- Make sure the Monitor cable is properly installed: monitor Cable is properly connected to the monitor.
- Analysis of computer sound “beep”: check and analysis of the sound that comes out on the pc speaker with a wide range of code.
The sound of ‘beep’ short 1 time, it means the system has done a Boot process properly.
The sound of ‘beep’ short 2 time, it means there is a problem on the configuration or settings in the CMOS.
The sound of ‘beep’ long 1 time and short 1 time, it means there is a problem on the Motherboard or DRAM.
The sound of ‘beep’ long 1 time and short 2 time, it means there is a problem on the monitor or VGA Card.
The sound of ‘beep’ long 1 time and short 3 time, it means there is a problem on the Keyboard.
The sound of ‘beep’ long 1 time and short 9 time, it means there is a problem on the ROM BIOS.
The sound of ‘beeps’ long continuous, it means there is a problem in DRAM.
The sound of ‘beeps’ short continuous, It means there is a problem receiving the voltage (power).
On some brands of Motherboards will emit beeps a few times when the temperature of the processors are too high (hot). Although there is a possibility there is also a difference in the sound of “beep” on any brand of motherboard doesn’t hurt you more able to observe and monitor troubleshooting that occurred on your computer. Because basically sound analysis it is not certainly in detecting and troubleshooting but could become the discourse for us when there a troubleshooting on our computer.
Hardware Detection Problems:
- Power Supply
- Motherboard
- Speaker
- RAM
- VGA Card + Monitor
- Keyboard
- Card I/O
- Disk Drive
If there is a problem with computer system still gives the appearance of a message on the monitor or accompanied by the sound of “beep” is 1 or 2 times, then chances are there are problems in the layout of the component numbers 6, 7, and 8 are on the Keyboard, Card i/o, and Disk drives.
If there is a problem with the system provides the code “beep” is more than 2 times, then chances are there are problems in the layout of the component numbers 4 and 5, i.e., RAM, VGA Card and Monitor.
As for the problem that is not accompanied by a message on the monitor or sound “beep” code, chances are there are problems on the component numbers 1 and 2, i.e. the Power Suplly and Motherboard.
For the initial stage, there is the first analysis where the computer hardware troubleshooting. Then you can revoke or relinquish the hardware approximately occurs troubleshooting then attach it back with for sure and check out exactly no leniency in return the hardware installation.
If there is still some undiscovered troubleshooting please check to the nearest computer service or authorized service center for your computer.