What's new

Closed Help paano set sa 3g 936 ko gusto lock kac sa 4g

Status
Not open for further replies.

raniel164

Eternal Poster
Joined
Jan 14, 2016
Posts
1,050
Reaction
313
Points
390
Age
28
help paano set sa 3g 936 ko gusto lock kac sa 4g at tyaka pa tut nadin mag openline
 
anu ibig sabihin ng full admin access boss? newbie kac kabibili ko lang 936 kanina kaso naka lock sa 4g ang hirap mag ip hunt kaya need ko kung paano maiset sa 2g,3g,4g kung. kaunti kac setting ng gui ko walang network settings
 
full admin boss machange mo ang settings ng APN mo

if full admin na ma access mo na network settings ng 936 mo boss
 
Untitled.png
 

Attachments

bakit naman boss pano pala yun hindi ma lock sa 4g kala ko para mag karoon ng setting na ganun ma debrand pa.
 
no need changing your firmware boss

Unlocking Instructions:
Step 1: Enter USB Mode (Steady Green Color)
a. Connect LAN cable from the LAN port of your modem to your PC and turn it on.
b. Run Multicast Upgrade Tool as administrator.
c. Make sure that your LAN card is properly chosen under “Network Card” option.


d. Under “File Path” option click “Open” and browse for the 931.bin file. Do not click “Start” at this point.



e. Unplug your modem.
f. Click “Start” in your Multicast Upgrade Tool.


g. Plug your modem and wait until the signal mode indicator displays a steady red color.
h. Press and hold “WPS” and “Power” buttons on your modem simultaneously until the signal mode indicator’s red color turns off twice, wait about 10 seconds then release the buttons.
i. Wait until the Mode indicator turns green and close Multicast Upgrade Tool.
j. Install Mobile Partner on your PC to provide the necessary USB drivers for your modem. If your operating system is windows 8 or above, install the “Huawei Drivers” provided.
k. Connect your modem to your PC via USB cable.
l. Take note of the COM port (Huawei UI interface) under LPT/COM ports in device manager.
Step 2: Run CID reader in USB mode and enter the following commands.
Note: select proper COM port in your CID reader before entering the codes below. To check if you have chosen the right COM Port, click on “Read Imei”. The “Logs” window should display the modem’s IMEI number otherwise select a different COM Port. Do not edit the codes unless you know what you are doing. You might brick your modem by doing so.
First code:

at ^ nvwrex = 8268,0,12,1,0,0,0,2,0,0,0, a, 0,0,0 ===>Unlocks the modem permanently.


Second code:

AT ^ SYSCFGEX = "0203", 3FFFFFFF, 1, 2, 800C5 ,, ===>Register to for 3G network first. If 3G is not available then LTE. Will not register if only 2G is available . All frequency bands are selected.

Third Code:
AT+CGDCONT=1,"IP","internet.globe.com.ph" ===> Set the APN to “internet.globe.com.ph” of the Globe Network to be connected to (use if sim is Globe Postpaid/LTE)
OR
AT+CGDCONT=1,"IP","http.globe.com.ph” ===> Set the APN to “http.globe.com.ph” of the Globe Network to be connected to (use if sim is Globe Prepaid/LTE)
OR
AT+CGDCONT=1,"IP","internet” ===> Set the APN to “internet” of the Smart Network to be connected to (use if sim is Smart Prepaid/LTE).







Fourth Code:
AT^reset ===> Reboots the modem.


3. Exit CID Reader
Congrats. Your modem is now unlocked.
How to Obtain Admin Access:
Enter USB mode by following Step 1 of “Unlocking Instructions”.
Run CID reader in USB mode and enter the following commands.
Note: select proper COM port in your CID reader before entering the codes below. To check if you have chosen the right COM Port, click on “Read Imei”. The “Logs” window should display the modem’s IMEI number otherwise select a different COM Port. Do not edit the codes unless you know what you are doing. You might brick your modem by doing so.


Enter the following commands:
First Code:
at^datalock? ===> Query Datalock Status Value. Default value is “1” (Enabled)

Second Code:
AT ^ NVWREX = 50502,0,128,4A FB 2D 5A 34 74 86 F0 A6 CC AE 46 99 53 83 1D 5C B1 7E 2A EF B2 B0 1A EF 53 03 8E C8 FF 1C 0D 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 8B 8C F4 B5 AF 0C F2 2C FE E0 F4 46 9C CF 47 95 36 71 1F 1C BF 05 7F 84 AB A9 F2 92 89 33 3C 01 00 00 12 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ===> Sets The Datalock Value to 12345678

Third Code:
at^datalock="12345678" ===> Sets Datalock Status value to “0” (Disabled)

Fourth Code:
at^sfm=1 ===> This will set your modem to factory mode

Fifth Code:
AT^reset ===> This will reset your modem. Wait until the modem reboots and shows a
steady power light indicator.



Connect your modem to your PC via USB Cable
Under “Network Properties”, Set IP manually as follows:
Tick “Use the Following IP Address”
IP address: 192.168.1.100
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1

Tick “Use the following DNS Server Adressess”
Preferred DNS: 192.168.1.1
Alternate DNS: (leave blank)

Click OK

Run “Config Updater” and wait for it to complete successfully.
Exit “Config Updater” and reboot modem.
Enter USB mode.
Run CID reader in USB mode and enter the following commands:
Code 1:
at^sfm=0 ===> This command will kick your modem out of factory mode
Code 2:
AT^reset ===> Resets and reboots the modem
After successfully rebooting, go to Network Properties again and Tick “Obtain IP Address Automatically” and “Obtain DNS Address Automatically”. Try to log into the modem’s web interface by typing 192.168.254.254 in your browser.

Enter the Following Information in the boxes provided.
Username: admin
Password: admin

Go to “Settings”.


Choose “Restore Default”
The modem will reboot.
Done. You now have admin access to your modem.
 
Last edited:
no need changing your firmware boss

Unlocking Instructions:
Step 1: Enter USB Mode (Steady Green Color)
a. Connect LAN cable from the LAN port of your modem to your PC and turn it on.
b. Run Multicast Upgrade Tool as administrator.
c. Make sure that your LAN card is properly chosen under “Network Card” option.


d. Under “File Path” option click “Open” and browse for the 931.bin file. Do not click “Start” at this point.



e. Unplug your modem.
f. Click “Start” in your Multicast Upgrade Tool.


g. Plug your modem and wait until the signal mode indicator displays a steady red color.
h. Press and hold “WPS” and “Power” buttons on your modem simultaneously until the signal mode indicator’s red color turns off twice, wait about 10 seconds then release the buttons.
i. Wait until the Mode indicator turns green and close Multicast Upgrade Tool.
j. Install Mobile Partner on your PC to provide the necessary USB drivers for your modem. If your operating system is windows 8 or above, install the “Huawei Drivers” provided.
k. Connect your modem to your PC via USB cable.
l. Take note of the COM port (Huawei UI interface) under LPT/COM ports in device manager.
Step 2: Run CID reader in USB mode and enter the following commands.
Note: select proper COM port in your CID reader before entering the codes below. To check if you have chosen the right COM Port, click on “Read Imei”. The “Logs” window should display the modem’s IMEI number otherwise select a different COM Port. Do not edit the codes unless you know what you are doing. You might brick your modem by doing so.
First code:

at ^ nvwrex = 8268,0,12,1,0,0,0,2,0,0,0, a, 0,0,0 ===>Unlocks the modem permanently.


Second code:

AT ^ SYSCFGEX = "0203", 3FFFFFFF, 1, 2, 800C5 ,, ===>Register to for 3G network first. If 3G is not available then LTE. Will not register if only 2G is available . All frequency bands are selected.

Third Code:
AT+CGDCONT=1,"IP","internet.globe.com.ph" ===> Set the APN to “internet.globe.com.ph” of the Globe Network to be connected to (use if sim is Globe Postpaid/LTE)
OR
AT+CGDCONT=1,"IP","http.globe.com.ph” ===> Set the APN to “http.globe.com.ph” of the Globe Network to be connected to (use if sim is Globe Prepaid/LTE)
OR
AT+CGDCONT=1,"IP","internet” ===> Set the APN to “internet” of the Smart Network to be connected to (use if sim is Smart Prepaid/LTE).







Fourth Code:
AT^reset ===> Reboots the modem.


3. Exit CID Reader
Congrats. Your modem is now unlocked.
How to Obtain Admin Access:
Enter USB mode by following Step 1 of “Unlocking Instructions”.
Run CID reader in USB mode and enter the following commands.
Note: select proper COM port in your CID reader before entering the codes below. To check if you have chosen the right COM Port, click on “Read Imei”. The “Logs” window should display the modem’s IMEI number otherwise select a different COM Port. Do not edit the codes unless you know what you are doing. You might brick your modem by doing so.


Enter the following commands:
First Code:
at^datalock? ===> Query Datalock Status Value. Default value is “1” (Enabled)

Second Code:
AT ^ NVWREX = 50502,0,128,4A FB 2D 5A 34 74 86 F0 A6 CC AE 46 99 53 83 1D 5C B1 7E 2A EF B2 B0 1A EF 53 03 8E C8 FF 1C 0D 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 8B 8C F4 B5 AF 0C F2 2C FE E0 F4 46 9C CF 47 95 36 71 1F 1C BF 05 7F 84 AB A9 F2 92 89 33 3C 01 00 00 12 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ===> Sets The Datalock Value to 12345678

Third Code:
at^datalock="12345678" ===> Sets Datalock Status value to “0” (Disabled)

Fourth Code:
at^sfm=1 ===> This will set your modem to factory mode

Fifth Code:
AT^reset ===> This will reset your modem. Wait until the modem reboots and shows a
steady power light indicator.



Connect your modem to your PC via USB Cable
Under “Network Properties”, Set IP manually as follows:
Tick “Use the Following IP Address”
IP address: 192.168.1.100
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1

Tick “Use the following DNS Server Adressess”
Preferred DNS: 192.168.1.1
Alternate DNS: (leave blank)

Click OK

Run “Config Updater” and wait for it to complete successfully.
Exit “Config Updater” and reboot modem.
Enter USB mode.
Run CID reader in USB mode and enter the following commands:
Code 1:
at^sfm=0 ===> This command will kick your modem out of factory mode
Code 2:
AT^reset ===> Resets and reboots the modem
After successfully rebooting, go to Network Properties again and Tick “Obtain IP Address Automatically” and “Obtain DNS Address Automatically”. Try to log into the modem’s web interface by typing 192.168.254.254 in your browser.

Enter the Following Information in the boxes provided.
Username: admin
Password: admin

Go to “Settings”.


Choose “Restore Default”
The modem will reboot.
Done. You now have admin access to your modem.
may link kaba nung tool boss?
 
nasa first link na nabigay ko syo boss,ano wala dun?
ayy oo nga pala
no need changing your firmware boss

Unlocking Instructions:
Step 1: Enter USB Mode (Steady Green Color)
a. Connect LAN cable from the LAN port of your modem to your PC and turn it on.
b. Run Multicast Upgrade Tool as administrator.
c. Make sure that your LAN card is properly chosen under “Network Card” option.


d. Under “File Path” option click “Open” and browse for the 931.bin file. Do not click “Start” at this point.



e. Unplug your modem.
f. Click “Start” in your Multicast Upgrade Tool.


g. Plug your modem and wait until the signal mode indicator displays a steady red color.
h. Press and hold “WPS” and “Power” buttons on your modem simultaneously until the signal mode indicator’s red color turns off twice, wait about 10 seconds then release the buttons.
i. Wait until the Mode indicator turns green and close Multicast Upgrade Tool.
j. Install Mobile Partner on your PC to provide the necessary USB drivers for your modem. If your operating system is windows 8 or above, install the “Huawei Drivers” provided.
k. Connect your modem to your PC via USB cable.
l. Take note of the COM port (Huawei UI interface) under LPT/COM ports in device manager.
Step 2: Run CID reader in USB mode and enter the following commands.
Note: select proper COM port in your CID reader before entering the codes below. To check if you have chosen the right COM Port, click on “Read Imei”. The “Logs” window should display the modem’s IMEI number otherwise select a different COM Port. Do not edit the codes unless you know what you are doing. You might brick your modem by doing so.
First code:

at ^ nvwrex = 8268,0,12,1,0,0,0,2,0,0,0, a, 0,0,0 ===>Unlocks the modem permanently.


Second code:

AT ^ SYSCFGEX = "0203", 3FFFFFFF, 1, 2, 800C5 ,, ===>Register to for 3G network first. If 3G is not available then LTE. Will not register if only 2G is available . All frequency bands are selected.

Third Code:
AT+CGDCONT=1,"IP","internet.globe.com.ph" ===> Set the APN to “internet.globe.com.ph” of the Globe Network to be connected to (use if sim is Globe Postpaid/LTE)
OR
AT+CGDCONT=1,"IP","http.globe.com.ph” ===> Set the APN to “http.globe.com.ph” of the Globe Network to be connected to (use if sim is Globe Prepaid/LTE)
OR
AT+CGDCONT=1,"IP","internet” ===> Set the APN to “internet” of the Smart Network to be connected to (use if sim is Smart Prepaid/LTE).







Fourth Code:
AT^reset ===> Reboots the modem.


3. Exit CID Reader
Congrats. Your modem is now unlocked.
How to Obtain Admin Access:
Enter USB mode by following Step 1 of “Unlocking Instructions”.
Run CID reader in USB mode and enter the following commands.
Note: select proper COM port in your CID reader before entering the codes below. To check if you have chosen the right COM Port, click on “Read Imei”. The “Logs” window should display the modem’s IMEI number otherwise select a different COM Port. Do not edit the codes unless you know what you are doing. You might brick your modem by doing so.


Enter the following commands:
First Code:
at^datalock? ===> Query Datalock Status Value. Default value is “1” (Enabled)

Second Code:
AT ^ NVWREX = 50502,0,128,4A FB 2D 5A 34 74 86 F0 A6 CC AE 46 99 53 83 1D 5C B1 7E 2A EF B2 B0 1A EF 53 03 8E C8 FF 1C 0D 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 8B 8C F4 B5 AF 0C F2 2C FE E0 F4 46 9C CF 47 95 36 71 1F 1C BF 05 7F 84 AB A9 F2 92 89 33 3C 01 00 00 12 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ===> Sets The Datalock Value to 12345678

Third Code:
at^datalock="12345678" ===> Sets Datalock Status value to “0” (Disabled)

Fourth Code:
at^sfm=1 ===> This will set your modem to factory mode

Fifth Code:
AT^reset ===> This will reset your modem. Wait until the modem reboots and shows a
steady power light indicator.



Connect your modem to your PC via USB Cable
Under “Network Properties”, Set IP manually as follows:
Tick “Use the Following IP Address”
IP address: 192.168.1.100
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1

Tick “Use the following DNS Server Adressess”
Preferred DNS: 192.168.1.1
Alternate DNS: (leave blank)

Click OK

Run “Config Updater” and wait for it to complete successfully.
Exit “Config Updater” and reboot modem.
Enter USB mode.
Run CID reader in USB mode and enter the following commands:
Code 1:
at^sfm=0 ===> This command will kick your modem out of factory mode
Code 2:
AT^reset ===> Resets and reboots the modem
After successfully rebooting, go to Network Properties again and Tick “Obtain IP Address Automatically” and “Obtain DNS Address Automatically”. Try to log into the modem’s web interface by typing 192.168.254.254 in your browser.

Enter the Following Information in the boxes provided.
Username: admin
Password: admin

Go to “Settings”.


Choose “Restore Default”
The modem will reboot.
Done. You now have admin access to your modem.
itong method na to boss opennline at debrand na pag ka tapos?
 
may link kaba nung tool boss?
tools na kailangan mo eh multicast tool,firmware ng 936,at cid reader
ayy oo nga pala

itong method na to boss opennline at debrand na pag ka tapos?
oo boss yung last nabigay ko fallow mo yan to unlock and full admin access,no need to change to polkom what so ever

tandaan start mo muna ang multicast tool mo.power and lan nakaunlug sa modem mo.first isaksak ang lan cable den ang power
 
Status
Not open for further replies.

Similar threads

Back
Top