What's new

Closed Galaxy j1 hard bricked

Status
Not open for further replies.
Natry mo naba mag flash tool? Or buhay paba yung recovery nya?

Kung nabubuhay pa yung recovery, search mo sa google pano iflash ang firmware via flashtool, asus zenfone 2 kase tong sakin different command kaya hindi ko masshare.
 
Ahh e full charge mo muna ang battery pag full charge na e download mode mona.. kahit hindi makapunta sa download mode.. still nag ru run parin yun..

Try mo na e flash.. kahit hind maglabas ang download mode nag rurun parin basta ok ang battery..
 
Natry mo naba mag flash tool? Or buhay paba yung recovery nya?

Kung nabubuhay pa yung recovery, search mo sa google pano iflash ang firmware via flashtool, asus zenfone 2 kase tong sakin different command kaya hindi ko masshare.
Sir bricked na po talaga.. di na sya pmupunta sa recovery or download mode. Maski charging po walang.. wala nang reponse yung phone sa kahit anung button. Usb jig nalang po yata pag asa ko.
 
Ahh e full charge mo muna ang battery pag full charge na e download mode mona.. kahit hindi makapunta sa download mode.. still nag ru run parin yun..

Try mo na e flash.. kahit hind maglabas ang download mode nag rurun parin basta ok ang battery..
Na try ko na din eh. Pero hndi na talaga sya nadedetect sa pc o odin.
 
How to make Samsung Galaxy S Download Mode JIG to solve if 3-Button combination failed
If you ever have a problem or getting trouble how to set the the Samsung Galaxy S and other Galaxy S I900 or Galaxy S II I9100 and other series into 'Download Mode' if pressing the three button combination (Volume down+Power+OK) failed or not working for some reasons while flashing the phone using ODIN. This solution may help solved your problem.

All you need is a good soldering skills, a little bit effort and creativity and some components and tools below.
* micro USB cable
* a 300K and 1K = 301K 1/4 watts Resistors (A 300K will work also)
* Soldering iron at least 20Watts and a soldering lead
* a cutter or knife
Procedures:
All you need is to solder the pin 4 (ID) and pin 5 (Ground) pins of the micro USB plug. Just cut out the sleeves of the USB plug, then attached and solder the 300K resistor across to pin 4 and 5. Just as like this finished product below:

How to use on Samsung Galaxy S while using ODIN.

1. Pull out the battery for about 2-5 minutes, then inplace it back again. Do not turn it ON yet.
2. Connect the jig you just made. Avoid touching the resistor and pins on the back or just put a a non inductive cover around it, an electrical tape works. The device will just turn into download mode in just a couple of seconds without pressing any buttons.

3. Once the Samsung Galaxy S displays the Downloading, disconnect the homemade jig USB plug and connect a regular USB cable from your PC to the phone, then you can flash the device using Odin.

Or to avoid any hassles or without any soldering skills ask Google where to find it.
It's very cheap to have it, but this USB Jig dongle will help you access to download mode even if your phone is 3-button combo disabled. If u plan on getting root access or adding ROM'S, you should have a dongle jig on hand just in case things do not go as planned. Download Mode Micro USB Jig will allow you to access the download mode on your Samsung Galaxy S Phone again.
Hope this might be of help
 
How to make Samsung Galaxy S Download Mode JIG to solve if 3-Button combination failed
If you ever have a problem or getting trouble how to set the the Samsung Galaxy S and other Galaxy S I900 or Galaxy S II I9100 and other series into 'Download Mode' if pressing the three button combination (Volume down+Power+OK) failed or not working for some reasons while flashing the phone using ODIN. This solution may help solved your problem.

All you need is a good soldering skills, a little bit effort and creativity and some components and tools below.
* micro USB cable
* a 300K and 1K = 301K 1/4 watts Resistors (A 300K will work also)
* Soldering iron at least 20Watts and a soldering lead
* a cutter or knife
Procedures:
All you need is to solder the pin 4 (ID) and pin 5 (Ground) pins of the micro USB plug. Just cut out the sleeves of the USB plug, then attached and solder the 300K resistor across to pin 4 and 5. Just as like this finished product below:

How to use on Samsung Galaxy S while using ODIN.

1. Pull out the battery for about 2-5 minutes, then inplace it back again. Do not turn it ON yet.
2. Connect the jig you just made. Avoid touching the resistor and pins on the back or just put a a non inductive cover around it, an electrical tape works. The device will just turn into download mode in just a couple of seconds without pressing any buttons.

3. Once the Samsung Galaxy S displays the Downloading, disconnect the homemade jig USB plug and connect a regular USB cable from your PC to the phone, then you can flash the device using Odin.

Or to avoid any hassles or without any soldering skills ask Google where to find it.
It's very cheap to have it, but this USB Jig dongle will help you access to download mode even if your phone is 3-button combo disabled. If u plan on getting root access or adding ROM'S, you should have a dongle jig on hand just in case things do not go as planned. Download Mode Micro USB Jig will allow you to access the download mode on your Samsung Galaxy S Phone again.
Hope this might be of help
Thanks for the ideas.. awesome
 
Natry mo naba mag flash tool? Or buhay paba yung recovery nya?

Kung nabubuhay pa yung recovery, search mo sa google pano iflash ang firmware via flashtool, asus zenfone 2 kase tong sakin different command kaya hindi ko masshare.
Paps hndi pwede sp flashtool sa samsung may sarili silang flasher ODIN tawag dun for mtk or mediatek lang sp flash tool
 
Ang pagkakaiba kasi ng samsung at mediatek device ang samsung phones pag nag flash ka via odin dapat buhay ung unit at mediatek naman patay ang unit pag nagflash
 
Not working yan..na try ko na..gagana lang ang usb jig pag nadedetect pa yung phone mo sa any usb ports
Papi ung samsung j1 ko na hard bricked ata after flasing sa odin ok naman ung fw kaso un nga no response na mga keys, triny ko usb jig pero no success di ko alam baka mali lang or shot ung ohms (300k, x3 100 ohms), nadedetect pa naman sya kaso as sprd u2s diag na lang sa port. Kaya pa kaya ijig to?
 
Status
Not open for further replies.

Similar threads

Back
Top