What's new

Tutorial Boost even mifi openline guide

zedicus said:
No, but I could get away with some explanations
Click to expand...
It's not that hard to find your way around it. Just install it, reboot your computer and you're good to go.
Run an instance of SWDownloader and try burning any firmware to any M028T device as this will put the device in download mode which is what we need.
After that, open BusHound and go to the device's section. Tick on the Marvell WTP device together with the "auto select hot plugged devices" checkbox as shown in the images I've provided.
That's it. You'll be ready to start capturing.
Now just plug any flashable modem and make sure you tick the 'Erase All Flash' option.
That's what I want captured.
 
xof said:
It's not that hard to find your way around it. Just install it, reboot your computer and you're good to go.
Run an instance of SWDownloader and try burning any firmware to any M028T device as this will put the device in download mode which is what we need.
After that, open BusHound and go to the device's section. Tick on the Marvell WTP device together with the "auto select hot plugged devices" checkbox as shown in the images I've provided.
That's it. You'll be ready to start capturing.
Now just plug any flashable modem and make sure you tick the 'Erase All Flash' option.
That's what I want captured.
Click to expand...
Should I complete the burning process or I should disconnect device just after the erasing process? Also where do I locate the log.txt?
 
Kronfour said:
Should I complete the burning process or I should disconnect device just after the erasing process? Also where do I locate the log.txt?
Click to expand...
You can complete the burning process. As long as the Erase all flash option is checked, it'll be good.
Hit the "Save" button next to "Capture", this will save the captured output as a text file.
Type anything on the comment section.. something like "successful_burn", select the "text file" radio button then hit save.
Type "successful_burn" under file name and choose any writable location to save the text file.
 
Sorry if I seem daft here but I can't seem to locate "Marvell WTP device" under the Devices option while SWD has been put to download mode too. Must I connect the device before the "Marvell WTP device" will be available?
I will try that after sending this message though.
 

Attachments

Kronfour said:
Sorry if I seem daft here but I can't seem to locate "Marvell WTP device" under the Devices option while SWD has been put to download mode too. Must I connect the device before the "Marvell WTP device" will be available?
I will try that after sending this message though.
Click to expand...
Yes.. the device has to be connected. Do this, flash the device like you normally would.
And while it's burning the firmware, go to the devices tab of Bus Hound and locate it (the Marvell WTP device)
Make sure to tick the "auto select hot plugged devices" checkbox so that it's selected automatically the next time it's plugged.
Then go again and flash the firmware for a second time, this time, go to the capture tab and select run on the lower right corner.
You should see some output.
 
I'm looking at an overwhelming amount of code, 3013 lines to be exact.
I was able to replicate some code on the device successfully thanks to Kronfour but unfortunately I'm yet to find a way to write the actual bits on the device itself.
Anyway.. I've got to keep on trying.
 
Well keep trying homie and try hard.:)
Anyway, it was a privilege I got the opportunity to help. Thanks to you too xof.
 
Last edited by a moderator:
Kronfour said:
Well keep trying homie and try hard.:)
Anyway, it was a privilege I got the opportunity to help. Thanks to you too xof.
Click to expand...
I'm glad I had someone like you who was adventurous enough to try all that.
Pushing commands to this device isn't that hard, the hardest part is writing those bits to the board's flash memory.
Looks like I'll have to write my own drivers lol. It's possible, but it looks like a lot of work.
Plus I never really liked C++.
 
Last edited by a moderator:
Hahaha:) I guess I should have taken my programming lectures at the university serious...
 
Last edited by a moderator:
I tried editing a certain source code which I stumbled upon but no joy. I edited out the parts of the code responsible for tripping the download process but it still wasn't working.
As it turns out, these functions are baked deep inside two DLL files which I can't edit.
So it looks like we'll be stuck with this one for a while.
 
When you make tutorials try to specify because I have already seen 2 versions of the L02C Modems for Cameroon I don't know if it's the same in India: L02CCameroon1_M023_LCD_V003 and L02CCameroon1_M023_LCD_V005 Oct 13 2016. The versions lower than V005 are easily flashable !
 
Bakit po ganun? Naopenline ko na FX PR2L ko 4G signal nya pag TM/Globe nakainsert pero pag Smart/TNT na hanggang 3G na lang. 4G naman to before ko inopenline e. Pahelp po kung pano mafix. Thank you!!

Eto po info ng device ko..
Software Version:
MoviMax_MV2_V003

Hardware Version:
LO2D_1_70
 
i know this is an old post but i'm sorry i need help flashing my MIFI model no M028T and my hardware version is L02B.. can anyone help to provide detailed procedures on flashing the firmwares... i have already downloaded them
 

Similar threads

Popular Tags

android apn card data dito ehi free internet free load freenet globe globe & tm gomo gtm hpi http injector injector internet load mobile mobile network modem network no load openline ovpn payload paymaya pldt pocket wifi postern promo proxy prx psiphon question registration remote proxy signal sim sim card sim registration smart ssh sun tm tnt tutorial unli vpn wifi

About this Thread

  • 316
    Replies
  • 87K
    Views
  • 86
    Participants
Last reply from:
rowel pagalan

New Topics

Popular On This Forum

Online statistics

Members online
547
Guests online
5,416
Total visitors
5,963
Back
Top