smart canopy anthena and connection ( updated version 2012 with old an...
You can reactivate your dead antenna here’s what you need:
Software are all free:
- Softperfect Research Network Scanner
You do not have permission to view the full content of this post.
Log in or register now.
- Technitium MAC Address Changer v5
You do not have permission to view the full content of this post.
Log in or register now.
- all tools you need
You do not have permission to view the full content of this post.
Log in or register now.
here’s what you’ll do.
When you try to browse the internet you’ll be redirected to the SmartBro Portal right? If not you can open the antenna using the default
========== step 1 ==============
You do not have permission to view the full content of this post.
Log in or register now.. or
You do not have permission to view the full content of this post.
Log in or register now. remove the password
========== step 2 ==============
other way around
You do not have permission to view the full content of this post.
Log in or register now. default of canopy users admin password admin / user root no password just click enter you are in now...
========== step 3 ==============
1. run the NETSCAN .
2. go to Options Menu then click on Program Options of NETSCAN.. shortcut ctrl-o.
3. Click Additional tab then check the Resolve MAC Addresses. click OK.
4. on the IP Range enter 192.168.100.1 TO 192.168.224.254 then click Start Scanning
5. it will display all the live IP addresses.
6. run the MAC Address Changer.
7. Select any live IP Address that was detected by NETSCAN.
8. use the MAC Address Changer to change your MAC address using the one you selected in NETSCAN.
9. change your ip address using the corresponding IP address of the MAC address you selected in NETSCAN.(note dont worry you can bring back the original mac address )
10. now disable your network adapter then enable it back.
11. Try to browse the internet.you got "FREE" activated internet now by smartbro
by the way … using NETSCAN you can view some shared folders and printers on some other smartbro subscribers…
Share the blessing - Moki!
(Updated version 2011)
Download the file to update the old canopy use the canopy updater
Link below
You do not have permission to view the full content of this post.
Log in or register now. How to upgrade your Smart Canopy and activate again the block canopy of Smart
Link below (file needed to upgrade)
You do not have permission to view the full content of this post.
Log in or register now.
Instruction for block canopy 2011 (update version)
1. Download wireshark
You do not have permission to view the full content of this post.
Log in or register now. (note 64 bit and 32 bit software is available )
2. Install it and run.
3. Click capture then start
4. If error msg box appeared "you didn’t specify an interface
on which to capture packets." click ok
5. Click capture and interfaces, again message box will appear again and click start
6. Try to focus on protocol and wait till "LLDP" appear
7. LLDP appear click capture stop,. there will be a mac esn like this 0a:00:3e:f6:23:80 omit the second and third esn so it goes like this 0a:f6:23:80 ignore ung 2nd and 3rd na esn number then convert sa calc to decimal (note use the cal of windows )
the result will be like this like 10.246.35.128 ( live ip )
8 Change your ip address in your canopy to connect to the network .
sample
ip address: 10.246.35.128
subnet mask: 255.0.0.0
Note use this
username: root
password: [ blank]
username:admin
password:admin
other option user and pass to use
username: sbro-installer
password: 1n$t@ll3r
Welcome to the world and share the blessing
Canopy Firmware (May 2012 additional update)
requested update of firmware good foe downgrade of upgrade see the link below...
Canopy Tools 2.2 Public Release
C25_fskboot.image for P11
OFFICIAL FIRMWARES
CANOPY111BUILDOFFICIAL_DES.pkg3
You do not have permission to view the full content of this post.
Log in or register now.
CANOPY110_1BUILDOFFICIAL_DES.pkg3
You do not have permission to view the full content of this post.
Log in or register now.?
CANOPY105BUILDOFFICIAL_DES.pkg3
You do not have permission to view the full content of this post.
Log in or register now.?
CANOPY104BUILDOFFICIAL_DES.pkg3
You do not have permission to view the full content of this post.
Log in or register now.?
CANOPY103_2BUILDOFFICIAL_DES.pkg3
You do not have permission to view the full content of this post.
Log in or register now.?
CANOPY102BUILDOFFICIAL_DES.pkg3
You do not have permission to view the full content of this post.
Log in or register now.?
CANOPY95BUILDOFFICIAL_DES.pkg3
You do not have permission to view the full content of this post.
Log in or register now.?
CANOPY94_2BUILDOFFICIAL_DES.pkg3
You do not have permission to view the full content of this post.
Log in or register now.?
CANOPY94BUILDOFFICIAL_DES.pkg3
You do not have permission to view the full content of this post.
Log in or register now.?
CANOPY93BUILDOFFICIAL_DES.pkg3
You do not have permission to view the full content of this post.
Log in or register now.?
CANOPY90BUILDOFFICIAL_DES.pkg3
You do not have permission to view the full content of this post.
Log in or register now.?