What's new

Closed Patolong po paano gumawa ng 12v power suply using 18 to 20 v tranpormer output

Status
Not open for further replies.

armiah13

Honorary Poster
Joined
Oct 2, 2016
Posts
238
Reaction
47
Points
136
At anong components ang gagamitin para maging 12v ang 18 to 20 v na tranpormer output. Dko kasi alam kong ilang amper tong transpormer na ito kasi malaki din ito..

Sana may mka tolong sakin ..impor tanti lang kasi to para sa project namn
 
wU96Ybq.png

sa AC in diyan mo ilagay ang output ng transformer mo na 18-20 volts

kung gusto mo tataas ang ampere niyan mag parallel ka lang ng 3-4 transistor na 2N3055

kailangang malagay sa heatsink si 2N3055
 

Attachments

wU96Ybq.png

sa AC in diyan mo ilagay ang output ng transformer mo na 18-20 volts

kung gusto mo tataas ang ampere niyan mag parallel ka lang ng 3-4 transistor na 2N3055

kailangang malagay sa heatsink si 2N3055
Ahm dko alam kong paano mag paralil po ng transistor po..
 

Attachments

Boss alam mo kong paano gagawa ng charger sa malalaki na battery ?

diba ang transistor ay may tatlong paa (base, collector, emitter ) lahat ng base ikabit mo ,lahat ng collector ganun din pati ang emitter
Ahh cge cge po salamt po sa tolong

Ahm sa plagay nyo po ilang amper kaya tong transpormer na ito. Malaki kasi ito ehh.. Bxta 18v ang outpot nya
 
Kung hindi naman ganun kalaki power requirements, puede rin ito..

hotobucket.com%2Falbums%2Fv496%2FScarEye%2Fdcpower.jpg


The resisitor under the LM317T is 240 Ohms, The resistor that is going to ground is 2K OHM, The Cap to the right is 47uf 35v, And the cap next to the diodes (bridge) is 4700uf 35v. Use 1N4001 rectifier diodes.

LM317T specs:
3 pin TO220 package
DC out 1.2v - 37v [adjustable]
1.5 ampere rating

Gamit ka lang breadboard PCB puede na yan, throughole 1 sided lang para sa small circuit kagaya niyan.
 

Attachments

ok po salamt
Kung hindi naman ganun kalaki power requirements, puede rin ito..

hotobucket.com%2Falbums%2Fv496%2FScarEye%2Fdcpower.jpg


The resisitor under the LM317T is 240 Ohms, The resistor that is going to ground is 2K OHM, The Cap to the right is 47uf 35v, And the cap next to the diodes (bridge) is 4700uf 35v. Use 1N4001 rectifier diodes.

LM317T specs:
3 pin TO220 package
DC out 1.2v - 37v [adjustable]
1.5 ampere rating

Gamit ka lang breadboard PCB puede na yan, throughole 1 sided lang para sa small circuit kagaya niyan.


ok po salamt po.. ahm pag aralan kopayan kasi nalilito kasi ako... hndi pa kasi ako maronong bomasa ng mga ganyan
Kung hindi naman ganun kalaki power requirements, puede rin ito..

hotobucket.com%2Falbums%2Fv496%2FScarEye%2Fdcpower.jpg


The resisitor under the LM317T is 240 Ohms, The resistor that is going to ground is 2K OHM, The Cap to the right is 47uf 35v, And the cap next to the diodes (bridge) is 4700uf 35v. Use 1N4001 rectifier diodes.

LM317T specs:
3 pin TO220 package
DC out 1.2v - 37v [adjustable]
1.5 ampere rating

Gamit ka lang breadboard PCB puede na yan, throughole 1 sided lang para sa small circuit kagaya niyan.
 

Attachments

Pwede din mag bridge type na powersupply gawin mo yung in3055 ata na diode yung code not sure but better check google for some advices.
 
Basic lang yan boss.
eto lang mga kaylangan mo!
~4Pcs 2amp diode
~10-15k ohms na Resistor
~Electrolytic Capacitor with capacitance of 25v and 3000 microfarad.
~LED indicator with 3-5k resistor
~switch (optional)
~fuse (optional)
.
Pero pwede rin dalawa ang output voltage na 12v-18v gamit ka potentiometer. (y)
CreepyTricks
 
Basic lang yan boss.
eto lang mga kaylangan mo!
~4Pcs 2amp diode
~10-15k ohms na Resistor
~Electrolytic Capacitor with capacitance of 25v and 3000 microfarad.
~LED indicator with 3-5k resistor
~switch (optional)
~fuse (optional)
.
Pero pwede rin dalawa ang output voltage na 12v-18v gamit ka potentiometer. (y)
CreepyTricks
pwede yang sinasabi mo tol kong mababa lang ang kailangan pero kong gagamitin sa audio amp. baka masunog ang potentiometer na sinasabi mo
 
pwede yang sinasabi mo tol kong mababa lang ang kailangan pero kong gagamitin sa audio amp. baka masunog ang potentiometer na sinasabi mo

Hindi boss meron ding desired na resistance depende sa taas ng voltage.
.
Nag aasemble kasi kami ng mga sound system kaya medyo expert na ko ;)

Ang variable Resistor ang magiging pinaka switch mo kung ano output voltage ang gagamitin mo (y)
 
Hindi boss meron ding desired na resistance depende sa taas ng voltage.
.
Nag aasemble kasi kami ng mga sound system kaya medyo expert na ko ;)
okey .. basta sa akin pag ganyang sitwasyon hindi talaga ako gugamit ng potentiometer na pang dropping sa B+ line lalo na high current ang kailangan
 
ah yes sir pag B+ talaga malakas ang voltage nya kaya Hot part ang tawag sa kanya (y)
iba kasi ang hot sa amin boss primary line yan at cold naman ang secondary line pag sa tv. naman dalawang klase ang HOT primary line , and horizontal output transformer
 
Status
Not open for further replies.
Back
Top