1. Welcome to PHCorner Forums. Take a moment to Sign up and gain unlimited access and extra privileges that guests are not entitled to, such as:

    All that and more! Registration is quick, simple and absolutely free. Join our community today!

Tutorial HUAWEI B315S-936 UNLOCKING AND ADMIN ACCESS

Discussion in 'WiMAX, DSL Modems' started by joongwanlee, Jan 25, 2016.

  1. HUAWEI B315S-936 UNLOCKING

    Unlocking Instructions:
    Step 1: Enter USB Mode (Steady Green Color)

    a. Connect LAN cable from the LAN port of your modem to your PC and turn it on.

    b. Run Multicast Upgrade Tool as administrator.

    c. Make sure that your LAN card is properly chosen under “Network Card” option.

    d. Under “File Path” option click “Open” and browse for the 931.bin file. Do not click “Start” at this point.

    e. Unplug your modem.

    f. Click “Start” in your Multicast Upgrade Tool.

    g. Plug your modem and wait until the signal mode indicator displays a steady red color.

    h. Press and hold “WPS” and “Power” buttons on your modem simultaneously until the signal mode indicator’s red color turns off twice, wait about 10 seconds then release the buttons.

    i. Wait until the Mode indicator turns green and close Multicast Upgrade Tool.

    j. Install Mobile Partner on your PC to provide the necessary USB drivers for your modem. If your operating system is windows 8 or above, install the “Huawei Drivers” provided.

    k. Connect your modem to your PC via USB cable.

    l. Take note of the COM port (Huawei UI interface) under LPT/COM ports in device manager.

    Step 2: Run CID reader in USB mode and enter the following commands.
    Note: select proper COM port in your CID reader before entering the codes below. To check if you have chosen the right COM Port, click on “Read Imei”. The “Logs” window should display the modem’s IMEI number otherwise select a different COM Port. Do not edit the codes unless you know what you are doing. You might brick your modem by doing so.

    First code:

    at ^ nvwrex = 8268,0,12,1,0,0,0,2,0,0,0, a, 0,0,0 ===>Unlocks the modem permanently.


    Second code:

    AT ^ SYSCFGEX = "0203", 3FFFFFFF, 1, 2, 800C5 ,, ===>Register to for 3G network first. If 3G is not available then LTE. Will not register if only 2G is available . All frequency bands are selected.

    Third Code:

    AT+CGDCONT=1,"IP","internet.globe.com.ph" ===> Set the APN to “internet.globe.com.ph” of the Globe Network to be connected to (use if sim is Globe Postpaid/LTE)

    OR

    AT+CGDCONT=1,"IP","http.globe.com.ph” ===> Set the APN to “http.globe.com.ph” of the Globe Network to be connected to (use if sim is Globe Prepaid/LTE)

    OR

    AT+CGDCONT=1,"IP","internet” ===> Set the APN to “internet” of the Smart Network to be connected to (use if sim is Smart Prepaid/LTE).


    Fourth Code:
    AT^reset ===> Reboots the modem.


    3. Exit CID Reader
    Congrats. Your modem is now unlocked.


    How to Obtain Admin Access:

    Enter USB mode by following Step 1 of “Unlocking Instructions”.
    Run CID reader in USB mode and enter the following commands.
    Note: select proper COM port in your CID reader before entering the codes below. To check if you have chosen the right COM Port, click on “Read Imei”. The “Logs” window should display the modem’s IMEI number otherwise select a different COM Port. Do not edit the codes unless you know what you are doing. You might brick your modem by doing so.


    Enter the following commands:
    First Code:
    at^datalock? ===> Query Datalock Status Value. Default value is “1” (Enabled)

    Second Code:
    AT ^ NVWREX = 50502,0,128,4A FB 2D 5A 34 74 86 F0 A6 CC AE 46 99 53 83 1D 5C B1 7E 2A EF B2 B0 1A EF 53 03 8E C8 FF 1C 0D 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 8B 8C F4 B5 AF 0C F2 2C FE E0 F4 46 9C CF 47 95 36 71 1F 1C BF 05 7F 84 AB A9 F2 92 89 33 3C 01 00 00 12 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ===> Sets The Datalock Value to 12345678

    Third Code:
    at^datalock="12345678" ===> Sets Datalock Status value to “0” (Disabled)

    Fourth Code:
    at^sfm=1 ===> This will set your modem to factory mode

    Fifth Code:
    AT^reset ===> This will reset your modem. Wait until the modem reboots and shows a
    steady power light indicator.



    Connect your modem to your PC via USB Cable
    Under “Network Properties”, Set IP manually as follows:
    Tick “Use the Following IP Address”
    IP address: 192.168.1.100
    Subnet Mask: 255.255.255.0
    Gateway: 192.168.1.1

    Tick “Use the following DNS Server Adressess”
    Preferred DNS: 192.168.1.1
    Alternate DNS: (leave blank)

    Click OK

    Run “Config Updater” and wait for it to complete successfully.
    Exit “Config Updater” and reboot modem.
    Enter USB mode.
    Run CID reader in USB mode and enter the following commands:
    Code 1:
    at^sfm=0 ===> This command will kick your modem out of factory mode
    Code 2:
    AT^reset ===> Resets and reboots the modem
    After successfully rebooting, go to Network Properties again and Tick “Obtain IP Address Automatically” and “Obtain DNS Address Automatically”. Try to log into the modem’s web interface by typing 192.168.254.254 in your browser.

    Enter the Following Information in the boxes provided.
    Username: admin
    Password: admin

    Go to “Settings”.

    Choose “Restore Default”
    The modem will reboot.
    Done. You now have admin access to your modem.

    Credits:
    Members sa Kabila (sir Freddy3K and others) who have provided the AT codes for unlocking as well as admin access.
     
    minders, Jovdav, deland and 13 others like this.
  2. ok na to salamat ts. mas madaling intindihin.
     
  3. Your Welcome
     
  4. Miggy1329

    Miggy1329 Addict Established

    Thank you po.ask lang din po ako if may command na pang lock sa 3g yung 936.salamat po
     
  5. Kung may mobile partner po kayo, set nyu setting ng mobile partner to " wcdma only "..
     
  6. Miggy1329

    Miggy1329 Addict Established

    Di kasi maread nang mobile partner.dapat po ba naka usb mode?panu po ba?
     
  7. Miggy1329

    Miggy1329 Addict Established

    Yan daw po ned na bin para sa full admin ng 936...di ko alam panu yan iflash sana may makagawa dto at ishare para sa phc.
     

    Attached Files:

    You must or Register to view Attachment.
  8. mulot

    mulot Enthusiast Established

    Naka-hide yung hex values.
     
  9. Miggy1329

    Miggy1329 Addict Established

    Kaya ng
    Kaya nga eh tapos panu kaya iflash may bin kasi ako di ko alam panu iflash
     
  10. mulot

    mulot Enthusiast Established

    di yan tinatanggap kahit anong firmware ang ipasok.
     
  11. jhella22

    jhella22 Addict Established

  12. sana may maglabas na ninto
     
  13. BlackArchAngelBlackArchAngel ano po tong admin access? nagawa po ba natin to sa modem ko? hihi :)
     
  14. Miggy1329

    Miggy1329 Addict Established

    Meron n nga po nakagawa ng full admin access may network mode na apn sms at iba pa...ayaw lang ishare kc nagbebnta ng 936..
     
    archjayr likes this.
  15. patulong naman na reset ko kase B593s-931 ko tapos hindi ako maka access sa 192.168.254.254 ano gagawin ko?
     
  16. May nakapag admin access na ba using this procedure? Pa feed back. Ts, joongwanleejoongwanlee , personally tested mo na ba ito?
     
  17. mulot

    mulot Enthusiast Established

    Yup, tested na po yan pero walang APN, SMS, etc. sa web gui.
     
    dorcasdomingo likes this.
  18. Ano kayang dapat na next step para mafull admin access na. Wala kasi ako 936 wala ako mapagexperimentuhan.
     
Tags / Keywords: