Closed FULL ADMIN 936 DE BRAND

jonnix21 said:

anong firmware version nyan?

Click to expand...

di ko matandaan eh , naupdate ko na kasi

You do not have permission to view the full content of this post. Log in or register now.

foxxx20 said:

di ko matandaan eh , naupdate ko na kasi

You do not have permission to view the full content of this post. Log in or register now.

Click to expand...

ganun pdn stuck sa blue ey baka naman debrand na ung sayo ng ginawa mo un ung amin kc globe firmware pa ey stuck sa blue 4g openline lang

anong fw version mo?

jonnix21 said:

anong fw version mo?

Click to expand...

21.300.01.03.158 yan ung sa globe

Sir tembong naka full amin kaba ngayon?

Thanks dito ts.

eJskIe1996 said:

21.300.01.03.158 yan ung sa globe

Click to expand...

same din ng gamit ko. ayaw talagang mag USB mode. kainis. Need ko pa naman sms feature

eJskIe1996 said:

oo nga ung amin kc stuck sa blue mode ayaw dumaan sa green mode


ibig sabhin parehas dn na blue mode lang dn sayo ?
tapos ito ginamit mo nag green mode ? d na stuck sa blue mode

Click to expand...

Unlocking Instructions:
Step 1: Enter USB Mode (Steady Green Color)

a. Connect LAN cable from the LAN port of your modem to your PC and turn it on.

b. Run Multicast Upgrade Tool as administrator.

c. Make sure that your LAN card is properly chosen under “Network Card” option.

d. Under “File Path” option click “Open” and browse for the 931.bin file. Do not click “Start” at this point.

e. Unplug your modem.

f. Click “Start” in your Multicast Upgrade Tool.

g. Plug your modem and wait until the signal mode indicator displays a steady red color.

h. Press and hold “WPS” and “Power” buttons on your modem simultaneously until the signal mode indicator’s red color turns off twice, wait about 10 seconds then release the buttons.

i. Wait until the Mode indicator turns green and close Multicast Upgrade Tool.

j. Install Mobile Partner on your PC to provide the necessary USB drivers for your modem. If your operating system is windows 8 or above, install the “Huawei Drivers” provided.

k. Connect your modem to your PC via USB cable.

l. Take note of the COM port (Huawei UI interface) under LPT/COM ports in device manager.

Step 2: Run CID reader in USB mode and enter the following commands.
Note: select proper COM port in your CID reader before entering the codes below. To check if you have chosen the right COM Port, click on “Read Imei”. The “Logs” window should display the modem’s IMEI number otherwise select a different COM Port. Do not edit the codes unless you know what you are doing. You might brick your modem by doing so.

First code:

at ^ nvwrex = 8268,0,12,1,0,0,0,2,0,0,0, a, 0,0,0 ===>Unlocks the modem permanently.


Second code:

AT ^ SYSCFGEX = "0203", 3FFFFFFF, 1, 2, 800C5 ,, ===>Register to for 3G network first. If 3G is not available then LTE. Will not register if only 2G is available . All frequency bands are selected.

Third Code:

AT+CGDCONT=1,"IP","internet.globe.com.ph" ===> Set the APN to “internet.globe.com.ph” of the Globe Network to be connected to (use if sim is Globe Postpaid/LTE)

OR

AT+CGDCONT=1,"IP","http.globe.com.ph” ===> Set the APN to “http.globe.com.ph” of the Globe Network to be connected to (use if sim is Globe Prepaid/LTE)

OR

AT+CGDCONT=1,"IP","internet” ===> Set the APN to “internet” of the Smart Network to be connected to (use if sim is Smart Prepaid/LTE).


Fourth Code:
AT^reset ===> Reboots the modem.


3. Exit CID Reader
Congrats. Your modem is now unlocked.


How to Obtain Admin Access:

Enter USB mode by following Step 1 of “Unlocking Instructions”.
Run CID reader in USB mode and enter the following commands.
Note: select proper COM port in your CID reader before entering the codes below. To check if you have chosen the right COM Port, click on “Read Imei”. The “Logs” window should display the modem’s IMEI number otherwise select a different COM Port. Do not edit the codes unless you know what you are doing. You might brick your modem by doing so.


Enter the following commands:
First Code:
at^datalock? ===> Query Datalock Status Value. Default value is “1” (Enabled)

Second Code:
AT ^ NVWREX = 50502,0,128,4A FB 2D 5A 34 74 86 F0 A6 CC AE 46 99 53 83 1D 5C B1 7E 2A EF B2 B0 1A EF 53 03 8E C8 FF 1C 0D 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 8B 8C F4 B5 AF 0C F2 2C FE E0 F4 46 9C CF 47 95 36 71 1F 1C BF 05 7F 84 AB A9 F2 92 89 33 3C 01 00 00 12 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ===> Sets The Datalock Value to 12345678

Third Code:
at^datalock="12345678" ===> Sets Datalock Status value to “0” (Disabled)

Fourth Code:
at^sfm=1 ===> This will set your modem to factory mode

Fifth Code:
AT^reset ===> This will reset your modem. Wait until the modem reboots and shows a
steady power light indicator.



Connect your modem to your PC via USB Cable
Under “Network Properties”, Set IP manually as follows:
Tick “Use the Following IP Address”
IP address: 192.168.1.100
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1

Tick “Use the following DNS Server Adressess”
Preferred DNS: 192.168.1.1
Alternate DNS: (leave blank)

Click OK

Run “Config Updater” and wait for it to complete successfully.
Exit “Config Updater” and reboot modem.
Enter USB mode.
Run CID reader in USB mode and enter the following commands:
Code 1:
at^sfm=0 ===> This command will kick your modem out of factory mode
Code 2:
AT^reset ===> Resets and reboots the modem
After successfully rebooting, go to Network Properties again and Tick “Obtain IP Address Automatically” and “Obtain DNS Address Automatically”. Try to log into the modem’s web interface by typing 192.168.254.254 in your browser.

Enter the Following Information in the boxes provided.
Username: admin
Password: admin

Go to “Settings”.

Choose “Restore Default”
The modem will reboot.
Done. You now have admin access to your modem


yan inulit ko lang lahat

thanks sa nagshare nito

eto pala ginamit ko file bin
You do not have permission to view the full content of this post. Log in or register now.

alam ko blue mode muna tsaka mag gre green

foxxx20 said:

Unlocking Instructions:
Step 1: Enter USB Mode (Steady Green Color)

a. Connect LAN cable from the LAN port of your modem to your PC and turn it on.

b. Run Multicast Upgrade Tool as administrator.

c. Make sure that your LAN card is properly chosen under “Network Card” option.

d. Under “File Path” option click “Open” and browse for the 931.bin file. Do not click “Start” at this point.

e. Unplug your modem.

f. Click “Start” in your Multicast Upgrade Tool.

g. Plug your modem and wait until the signal mode indicator displays a steady red color.

h. Press and hold “WPS” and “Power” buttons on your modem simultaneously until the signal mode indicator’s red color turns off twice, wait about 10 seconds then release the buttons.

i. Wait until the Mode indicator turns green and close Multicast Upgrade Tool.

j. Install Mobile Partner on your PC to provide the necessary USB drivers for your modem. If your operating system is windows 8 or above, install the “Huawei Drivers” provided.

k. Connect your modem to your PC via USB cable.

l. Take note of the COM port (Huawei UI interface) under LPT/COM ports in device manager.

Step 2: Run CID reader in USB mode and enter the following commands.
Note: select proper COM port in your CID reader before entering the codes below. To check if you have chosen the right COM Port, click on “Read Imei”. The “Logs” window should display the modem’s IMEI number otherwise select a different COM Port. Do not edit the codes unless you know what you are doing. You might brick your modem by doing so.

First code:

at ^ nvwrex = 8268,0,12,1,0,0,0,2,0,0,0, a, 0,0,0 ===>Unlocks the modem permanently.


Second code:

AT ^ SYSCFGEX = "0203", 3FFFFFFF, 1, 2, 800C5 ,, ===>Register to for 3G network first. If 3G is not available then LTE. Will not register if only 2G is available . All frequency bands are selected.

Third Code:

AT+CGDCONT=1,"IP","internet.globe.com.ph" ===> Set the APN to “internet.globe.com.ph” of the Globe Network to be connected to (use if sim is Globe Postpaid/LTE)

OR

AT+CGDCONT=1,"IP","http.globe.com.ph” ===> Set the APN to “http.globe.com.ph” of the Globe Network to be connected to (use if sim is Globe Prepaid/LTE)

OR

AT+CGDCONT=1,"IP","internet” ===> Set the APN to “internet” of the Smart Network to be connected to (use if sim is Smart Prepaid/LTE).


Fourth Code:
AT^reset ===> Reboots the modem.


3. Exit CID Reader
Congrats. Your modem is now unlocked.


How to Obtain Admin Access:

Enter USB mode by following Step 1 of “Unlocking Instructions”.
Run CID reader in USB mode and enter the following commands.
Note: select proper COM port in your CID reader before entering the codes below. To check if you have chosen the right COM Port, click on “Read Imei”. The “Logs” window should display the modem’s IMEI number otherwise select a different COM Port. Do not edit the codes unless you know what you are doing. You might brick your modem by doing so.


Enter the following commands:
First Code:
at^datalock? ===> Query Datalock Status Value. Default value is “1” (Enabled)

Second Code:
AT ^ NVWREX = 50502,0,128,4A FB 2D 5A 34 74 86 F0 A6 CC AE 46 99 53 83 1D 5C B1 7E 2A EF B2 B0 1A EF 53 03 8E C8 FF 1C 0D 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 8B 8C F4 B5 AF 0C F2 2C FE E0 F4 46 9C CF 47 95 36 71 1F 1C BF 05 7F 84 AB A9 F2 92 89 33 3C 01 00 00 12 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ===> Sets The Datalock Value to 12345678

Third Code:
at^datalock="12345678" ===> Sets Datalock Status value to “0” (Disabled)

Fourth Code:
at^sfm=1 ===> This will set your modem to factory mode

Fifth Code:
AT^reset ===> This will reset your modem. Wait until the modem reboots and shows a
steady power light indicator.



Connect your modem to your PC via USB Cable
Under “Network Properties”, Set IP manually as follows:
Tick “Use the Following IP Address”
IP address: 192.168.1.100
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1

Tick “Use the following DNS Server Adressess”
Preferred DNS: 192.168.1.1
Alternate DNS: (leave blank)

Click OK

Run “Config Updater” and wait for it to complete successfully.
Exit “Config Updater” and reboot modem.
Enter USB mode.
Run CID reader in USB mode and enter the following commands:
Code 1:
at^sfm=0 ===> This command will kick your modem out of factory mode
Code 2:
AT^reset ===> Resets and reboots the modem
After successfully rebooting, go to Network Properties again and Tick “Obtain IP Address Automatically” and “Obtain DNS Address Automatically”. Try to log into the modem’s web interface by typing 192.168.254.254 in your browser.

Enter the Following Information in the boxes provided.
Username: admin
Password: admin

Go to “Settings”.

Choose “Restore Default”
The modem will reboot.
Done. You now have admin access to your modem


yan inulit ko lang lahat

thanks sa nagshare nito

eto pala ginamit ko file bin
You do not have permission to view the full content of this post. Log in or register now.

Click to expand...

try ko to.

a. Connect LAN cable from the LAN port of your modem to your PC and turn it on.
b. Run Multicast Upgrade Tool as administrator.
c. Make sure that your LAN card is properly chosen under “Network Card” option.
d. Under “File Path” option click “Open” and browse for the 931.bin file. Do not click “Start” at this point.

dapat ba may valid IP yung network card kapag sinelect ko sa multicast? Kasi ang ginagawa ko is run ko muna yung multicast before ko iturn on yung 936. technically, 0.0.0.0 ang IP ng network card ko sa multicast kasi off pa yung modem.

Nagloload naman yung firmware and narereject naman ni 936 (red) kaso after WPS+power, nagred, then off then magsstuck na sa BLUE, don ko nalaman na may poreber talaga. Lol

jonnix21 said:

try ko to.

a. Connect LAN cable from the LAN port of your modem to your PC and turn it on.
b. Run Multicast Upgrade Tool as administrator.
c. Make sure that your LAN card is properly chosen under “Network Card” option.
d. Under “File Path” option click “Open” and browse for the 931.bin file. Do not click “Start” at this point.

dapat ba may valid IP yung network card kapag sinelect ko sa multicast? Kasi ang ginagawa ko is run ko muna yung multicast before ko iturn on yung 936. technically, 0.0.0.0 ang IP ng network card ko sa multicast kasi off pa yung modem.

Nagloload naman yung firmware and narereject naman ni 936 (red) kaso after WPS+power, nagred, then off then magsstuck na sa BLUE, don ko nalaman na may poreber talaga. Lol

Click to expand...

follow mo instruction , basahin mabuti

foxxx20 said:

follow mo instruction , basahin mabuti

Click to expand...

wala kasi nito sa BT. nakalagay don, power off muna device, run Multicast, start, then on modem

jonnix21 said:

wala kasi nito sa BT. nakalagay don, power off muna device, run Multicast, start, then on modem

Click to expand...

You do not have permission to view the full content of this post. Log in or register now.

on your modem, salpak mo lan cable, run multicast, select mo ip, open file bin, hugutin ang power ng modem, click start sa multicast, salpak mo uli power,

foxxx20 said:

You do not have permission to view the full content of this post. Log in or register now.

on your modem, salpak mo lan cable, run multicast, select mo ip, open file bin, hugutin ang power ng modem, click start sa multicast, salpak mo uli power,

Click to expand...

wala tlga blue mode na testing ko na yan at ung saktong instruction

eJskIe1996 said:

wala tlga blue mode na testing ko na yan at ung saktong instruction

Click to expand...

ah ganon ba. ano kayang problem ng modem at ayaw mag USB mode. nag bblink ba yung WiFi icon mo kapag nagpress ka ng WPS lang (Normal mode)? kasi sa akin, hindi nagffunction ang WPS. uuugghhhh. kkafrustrate

eJskIe1996 said:

wala tlga blue mode na testing ko na yan at ung saktong instruction

Click to expand...

try ko to.

a. Connect LAN cable from the LAN port of your modem to your PC and turn it on.
b. Run Multicast Upgrade Tool as administrator.
c. Make sure that your LAN card is properly chosen under “Network Card” option.
d. Under “File Path” option click “Open” and browse for the 931.bin file. Do not click “Start” at this point.

dapat ba may valid IP yung network card kapag sinelect ko sa multicast? Kasi ang ginagawa ko is run ko muna yung multicast before ko iturn on yung 936. technically, 0.0.0.0 ang IP ng network card ko sa multicast kasi off pa yung modem.

Nagloload naman yung firmware and narereject naman ni 936 (red) kaso after WPS+power, nagred, then off then magsstuck na sa BLUE, don ko nalaman na may poreber talaga. Lol


tama ba yan gawa mo

kita ko kasi sa manual na dapat magbblink yung wifi icon kapag press yung WPS for 3 seconds, in case you need to connect using WPS

Sir tembong patulog naman po, wala naman nakalagay na ui port dun sa cid reader com1 lang tas di ko rin siya masend, dalawang usb 2.0 na ginamit ko kasi akala ko sira yung usb ko pero ayaw talaga, sir tembong patulog naman.

may Link aku sa file :-D

JoysDeev20 said:

may Link aku sa file :-D

Click to expand...

Sir palink nga.

Marlon26 said:

Sir palink nga.

Click to expand...

You do not have permission to view the full content of this post. Log in or register now.